Please wait while we load your article...

Home > Density

Learn more about "Density"

Density

The '''density''' of a material is defined as its mass per unit volume:
-

\rho = \frac{m}{V}

Different materials usually have different densities, so density is an important concept regarding buoyancy, metal purity and packaging. In some cases density is expressed as the dimensionless quantities specific gravity or relative density, in which case it is expressed in multiples of the density of some other standard material, usually water or air.

History

In a well-known story, Archimedes was given the task of determining whether Hiero II of Syracuse|King Hiero's goldsmith was embezzling gold during the manufacture of a wreath dedicated to the gods and replacing it with another, cheaper alloy.Archimedes, A Gold Thief and Buoyancy - by Larry "Harris" Taylor, Ph.D. Archimedes knew that the irregularly shaped wreath could be crushed into a cube whose volume could be calculated easily and compared with the weight; but the king did not approve of this. Baffled, Archimedes took a bath and observed from the rise of the water upon entering that he could calculate the volume of the crown through the Displacement (fluid)|displacement of the water. Allegedly, upon this discovery, he went running naked though the streets shouting, "Eureka! Eureka!" (Greek "I found it"). As a result, the term "Eureka (word)|eureka" entered common parlance and is used today to indicate a moment of enlightenment. This story first appeared in written form in Vitruvius' De architectura|books of architecture, two centuries after it supposedly took place.Vitruvius on Architecture, Book IX, paragraphs 9-12, translated into English and in the original Latin. Some scholars have doubted the accuracy of this tale, saying among other things that the method would have required precise measurements that would have been difficult to make at the time. The first Eureka moment, ''Science'' '''305''': 1219, August 2004.Fact or Fiction?: Archimedes Coined the Term "Eureka!" in the Bath, ''Scientific American'', December 2006.

Measurement of density

For a homogeneous object, the mass divided by the volume gives the density. The mass is normally measured with an appropriate weighing scale|scale or balance; the volume may be measured directly (from the geometry of the object) or by the displacement of a fluid. If the body is inhomogeneous, the density is a function of the coordinates

\rho(\vec{r})=dm/dv

, where

dv

is elementary volume with coordinates

\vec{r}

. The mass of the body then can be expressed as
-

m = \int_V \rho(\vec{r})dv

, where the integration is over the volume of the body ''V''. A very common instrument for the direct measurement of the density of a liquid is the hydrometer, which measures the volume displaced by an object of known mass. A common laboratory device for measuring fluid density is a pycnometer; a related device for measuring the absolute density of a solid is a gas pycnometer. Another instrument used to determine the density of a liquid or a gas is the digital density meter - based on the oscillating U-tube principle. The density of a solid material can be ambiguous, depending on exactly how its volume is defined, and this may cause confusion in measurement. A common example is sand: if gently filled into a container, the density will be low; when the same sand is compacted into the same container, it will occupy less volume and consequently exhibit a greater density. This is because sand, like all powders and granular solids contains a lot of air space in between individual grains; this overall density is called the bulk density, which differs significantly from the density of an individual grain of sand.

Common units

The SI unit for density is:
- kilograms per cubic metre (kg/m³) Metric units outside the SI
- kilograms per litre (kg/L). Water generally has a density around 1 kg/L, making this a convenient unit.
- kilograms per cubic decimeter (kg/dm³)
- grams per millilitre (g/mL),
- grams per cubic centimeter (g/cc or g/cm³). These are numerically equivalent to kg/L (1 kg/L = 1 kg/dm³ = 1 g/cm³ = 1 g/mL). In US customary units|U.S. customary units or Imperial units, the units of density include:
- ounces per cubic inch (oz/cu in)
- Pound (mass)|pounds per cubic inch (lb/cu in)
- pounds per cubic foot (lb/cu ft)
- pounds per cubic yard (lb/cu yd)
- pounds per gallon (for U.S. or imperial gallons) (lb/gal)
- pounds per U.S. bushel (lb/bu)
- slug (mass)|slugs per cubic foot.

Changes of density

In general density can be changed by changing either the pressure or the temperature. Increasing the pressure will always increase the density of a material. Increasing the temperature generally decreases the density, but there are notable exceptions to this generalisation. For example, the density of water increases between its melting point at 0 °C and 4 °C and similar behaviour is observed in silicon at low temperatures. The effect of pressure and temperature on the densities of liquids and solids is small so that a typical compressibility for a liquid or solid is 10^–6 bar (unit)|bar^–1 (1 bar=0.1 MPa) and a typical thermal expansivity is 10^–5 Kelvin|K^–1. In contrast, the density of gases is strongly affected by pressure. Boyle's law says that the density of an ideal gas is given by
-

\rho = \frac {MP}{RT}

where

R

is the Gas constant|universal gas constant,

P

is the pressure,

M

the molar mass, and

T

the absolute temperature. This means that a gas at 300 Kelvin|K and 1 bar (unit)|bar will have its density doubled by increasing the pressure to 2 bar (unit)|bar or by reducing the temperature to 150 Kelvin|K. Iridium is the densest known substance at standard conditions for temperature and pressure.